Short answer. When CCTV timestamps disagree with a gate log, alarm alert or incident report, record what each source displays and what its timestamp represents. Compare the recorder with a reliable time reference before changing any settings. Use the measured difference to guide the footage search, preserve the relevant original recording through your authorised process, and keep any estimated incident time separate from the times displayed by the systems.

For example, a warehouse supervisor may report a vehicle movement at about 21:10, while the recorder shows the matching clip at 21:03. A gate system might log when it accepted a credential and the supervisor might be recalling when they saw the vehicle move. Before putting the three entries in order, establish which events they describe and which clocks produced their times.

Check what each timestamp measures

Ask whoever owns each record to identify its source. On CCTV, compare the time overlay on the picture, the recorder’s playback timeline and the time shown by the export player where available. If those displays disagree, record which one you used to find and export the clip. The file’s creation time can reflect when the export was made.

For other logs, label the event behind each time. A door controller can record a credential read, a door contact can record an opening, and a monitoring centre can record when a signal arrived. An officer’s note may record the time a call was taken or an estimate of when a witness saw something. Record each entry with its source, date, time zone where known, and whether it is a system reading or a person’s estimate.

Measure the recorder’s difference before anyone adjusts it

  1. Ask an authorised operator to compare the recorder’s current displayed date and time with a reliable reference as close to the same instant as practical.
  2. Write both readings together, along with the reference used, the system checked, and its time zone or UTC offset if known. Describe the direction in words, such as “recorder seven minutes slow”.
  3. Check each relevant recorder or platform separately. A temporary CCTV tower and the building’s recorder may each have their own clock. Keep the measured difference tied to the specific device and check time.

The UK guidance on recovery and acquisition of video evidence recommends comparing system time with an accurate reference and recording the difference in the audit trail. The police requirements for CCTV systems also call for the system clock to be maintained, taking account of GMT and British Summer Time.

Use the difference to find the clip

Suppose a simultaneous check reads 21:22 GMT on the reference and 21:15 on the recorder, and both are using GMT. The recorder is seven minutes slow at the time of the check. For a reported event around 21:10 GMT, start near 21:03 on that recorder’s playback timeline. Search enough time either side to account for how approximate the report is and what the check established.

Where possible, compare a distinct event that appears in more than one authorised record, such as a clearly identifiable barrier movement. Use the same physical event for comparison. A barrier opening can follow a successful credential read, so a gap between the two may be real even when the clocks agree.

If the recorder restarted, its clock was changed, or the recording crosses a time-zone or clock change, a difference measured now may apply to only part of the timeline. Ask the responsible system administrator or investigator to help narrow the relevant window. Keep the original times and mark any reconstructed time as an estimate with the basis for that estimate.

Preserve the recording and hand over the uncertainty

Escalate early if the relevant footage is approaching routine overwrite. The authorised operator should follow the site’s preservation process and record the footage selected using its original displayed times, the device identifier, the export time and the incident reference. Keep any timing explanation alongside the recording. If a viewing copy is made, label it separately and retain the original export through the approved process.

A useful handover might read: “Reference 21:22 GMT, recorder 21:15 at the same check. Recorder seven minutes slow at check time. Reviewed playback around 21:03 for the reported 21:10 GMT event. Timing at the incident remains an estimate.” Add the operator, date and footage reference in the restricted incident record. For decisions about sending material to another party, see the separate guide to preserving and releasing CCTV footage after an incident.

Give the clock correction to the system owner

Once the relevant records have been secured and the system owner has agreed the timing of the work, have an authorised administrator correct the configuration. Ask them to record when the change happened and verify it against the reference using a fresh test recording and playback or export. Keep the correction date in the incident record so later reviewers can tell which recordings were made before and after it.

If your site needs a clearer handover between guarding staff and the people who operate the camera system, see our commercial CCTV service information or discuss your site requirements with K9 Security Services.

Featured image is illustrative and shows a mobile CCTV tower beside a construction boundary at night.

Leave A Comment